The use of extraction technique with disposable tips (DPX) was applied for the first time for the extraction and preconcentration of Yb in samples of liquid waste from the petrochemical industry and environmental water using bioabsorbent cork. The use of cork as an extracting phase in the determination of Yb by high-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GF AAS) was evaluated. The pyrolysis and atomization temperatures were optimized at 1400 and 2400 °C, respectively. H2SO4, HNO3 and HCl acids were compared in the steps of cleaning the extraction phase and desorption of the analyte by DPX. The best extraction in the selected conditions was obtained with pH 8.0 and 5% v/v HCl. The recoveries were close to 100% for residual water and drinking water, 33 to 77% for produced water and 64 to 93% for river water. Tests with interfering ions in different concentrations were performed. The relative limit of quantification (LOQ) and limit of detection (LOD) were estimated at 0.03 and 0.01 µg L-1, respectively. The total time for the preparation of the samples by DPX was close to 1 min per sample. Extraction and pre-concentration were observed using DPX with a pre-enrichment factor of approximately 4 times.

The assessment of chlorine, fluorine, and sulfur concentrations in depth profile of drill cuttings was performed using ion chromatography after sample preparation by pyrohydrolysis. The parameters for pyrohydrolysis were optimized using a Box-Behnken design, and the established conditions were 300 mg of sample, 300 mg of V2O5, temperature of 1000 °C, reaction time of 25 min, and absorbing solution of 50 mmol L-1 NH3 + 150 mmol L-1 H2O2. The accuracy was evaluated by the analysis of certified reference materials and recovery tests, and the results showed a good agreement between determined and certified values and recoveries (89-108%). The precision (relative standard deviation (RSD) < 10%), and the limits of detection (0.5-2.5 mg kg 1) were suitable for drill cuttings analysis. The concentration of chlorine, fluorine, and sulfur in drill cuttings at different depths was at mg g-1 range, and its variation is related to the mineral composition of the samples.

A method for chlorine determination in crude oil samples, through the formation of MgCl molecule, by high-resolution continuum source graphite furnace molecular absorption spectrometry (HR-CS GF MAS) was developed and is described in this paper. The use of this molecule for chlorine determination in crude oil has not been reported up to now. Measures were carried out at the wavelength 377.010 nm and the samples were submitted to a simple treatment as emulsion, whose composition was optimized applying a simplex-centroid experimental design. Magnesium was used as molecule forming agent at the concentration of 10 g L-1, at least 500 times higher than the concentration of chlorine. This excess is required to ensure the molecule formation of all content of Cl present in the sample. Chemical modifier Pd was used and improved greatly the signal intensities. Optimized pyrolysis and vaporization temperatures, applied for determination, were 800 and 2300 °C, respectively. Accuracy was evaluated through analysis of certified reference materials, NIST 1848 and NIST 1634c, and addition and recovery tests with recoveries between 92 and 117%. Limits of detection and quantification were 3.0 and 9.0 µg g-1, respectively. The method was applied to eight crude oil samples.

The simultaneous determination of thorium and uranium in mineral fertilizers by inductively coupled plasma optical emission spectrometry (ICP OES) was optimized. The three-level factorial design was applied to optimize the operating conditions of radiofrequency power and nebulizer gas flow rate. The analytical method was specific and selective for both elements.

A fast, simple and reliable method for Hg determination in green coke and oily sludge samples by atomic fluorescence spectrometry is described. Microwave digestion and extraction procedures were evaluated for highly complex samples of coke and oily sludge. The concentrations of SnCl2 and HCl to promote Hg vapor, were optimized, as well as the concentration of KMnO4, to stabilize the Hg2+ before the atomic vapor formation. Accuracy of the method was evaluated through certified reference material, for green coke, and comparison with cold vapor atomic absorption spectrometry (CV AAS), for oily sludge. Recovery tests were also performed. Limits of detection and quantification were 0.8 and 2.6 µg kg−1, respectively. Ten green coke and nine sludge samples were analysed and Hg concentrations in coke are very low, between 0.005 and 0.065 mg kg−1, but oily sludge samples have high concentrations, ranging from 42.5 to 376.6 mg kg−1, requiring careful management.